D2JW Sealed Ultra Subminiature Basic Switch
Ultra-small and Highly Sealed
- Degree of protection for the molded lead wire models conforms to IEC IP67.(Lead wire type only)
- Wide range of operating temperature from -40ºC to 85ºC.
- Gold-alloy crossbar contact and coil spring offer long life expectancy and high contact reliability.
Model | 2D/3D CAD | |
---|---|---|
D2JW-011 | Download | |
D2JW-011-MD | Download | |
D2JW-012-MD | Download | |
D2JW-013-MD | Download | |
D2JW-01K11 | Download | |
D2JW-01K11-MD | Download | |
D2JW-01K12-MD | Download | |
D2JW-01K13-MD | Download | |
D2JW-01K1A1 | Download | |
D2JW-01K1A1-MD | Download | |
D2JW-01K1A2-MD | Download | |
D2JW-01K1A3-MD | Download | |
D2JW-01K21 | Download | |
D2JW-01K21-MD | Download | |
D2JW-01K22-MD | Download | |
D2JW-01K23-MD | Download | |
D2JW-01K31 | Download | |
D2JW-01K31-MD | Download | |
D2JW-01K32-MD | Download | |
D2JW-01K33-MD | Download |

Actuator | Contact form | Model | |
---|---|---|---|
Solder terminals | Molded lead wires | ||
Pin plunger
|
SPDT | D2JW-011 | D2JW-011-MD |
SPST-NC | --- | D2JW-012-MD | |
SPST-NO | --- | D2JW-013-MD | |
Short hinge lever
|
SPDT | D2JW-01K1A1 | D2JW-01K1A1-MD |
SPST-NC | --- | D2JW-01K1A2-MD | |
SPST-NO | --- | D2JW-01K1A3-MD | |
Hinge lever
|
SPDT | D2JW-01K11 | D2JW-01K11-MD |
SPST-NC | --- | D2JW-01K12-MD | |
SPST-NO | --- | D2JW-01K13-MD | |
Hinge roller lever
|
SPDT | D2JW-01K21 | D2JW-01K21-MD |
SPST-NC | --- | D2JW-01K22-MD | |
SPST-NO | --- | D2JW-01K23-MD | |
Simulated roller hinge lever
|
SPDT | D2JW-01K31 | D2JW-01K31-MD |
SPST-NC | --- | D2JW-01K32-MD | |
SPST-NO | --- | D2JW-01K33-MD |
Contact Form
SPDT
*The color in parentheses indicates the color of the lead wire.
Electrical ratings | 0.1 A at 30 VDC (resistive load) |
---|
The ratings values apply under the following test conditions: | |
Ambient temperature: 20 ±2ºC Ambient humidity: 65± 5% Operating frequency: 30 operations/min |
Characteristics
Permissible operating speed (see note 2) |
1 mm to 250 mm/s |
---|---|
Permissible operating frequency | Mechanical: 240 operations/min max. Electrical: 30 operations/min max. |
Insulation resistance | 100 MΩ min. (at 500 VDC) |
Contact resistance (initial value) | 100 mΩ max. (molded lead wire models: 140 mΩ max.) |
Dielectric strength * 1 |
600 VAC, 50/60 Hz for 1 min between terminals of the same polarity 1,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts |
Vibration resistance * 2 |
Malfunction: 10 to 55 Hz, 1.5-mm double amplitude |
Shock resistance |
Destruction: 1,000 m/s2 {approx. 100G} max. Malfunction * 2: 200 m/s2 {approx. 20G} max. |
Durability * 3 | Mechanical: 1,000,000 operations min.(60 operations/min) Electrical: 100,000 operations min.(30 operations/min) |
Degree of protection | IEC IP67 (excluding the terminals on terminal models) |
Degree of protection against electric shock | Class I |
Proof tracking index (PTI) | 175 |
Ambient operating temperature | -40ºC to +85ºC (at ambient humidity of 60% max.)(with no icing or condensation) |
Ambient operating humidity | 35% to 98% (for +5ºC to +35ºC) |
Weight | Approx. 7 g (pin plunger models with molded lead wire models) |
Note: | The data given above are initial values. | |
* 1. | The dielectric strength values shown apply for use with Separator (refer to page 4). | |
* 2. | For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, they apply at the total travel position. Close or open circuit of the contact is 1ms max. | |
* 3. | For testing conditions, consult your OMRON sales representative. |
|
|||||||||||||
|
|||||||||||||
|
|||||||||||||
|
|||||||||||||
|
|||||||||||||
|
|||||||||||||
|
Cautions
●Terminal Connection
Before soldering the lead wire to the terminal, first insert the lead wire conductor through the terminal hole.
Complete the soldering at the iron tip temperature till 250°C within 3 seconds, and do not apply any external force for 1 minute after soldering. Soldering at an excessively high temperature or soldering for more than 3 seconds may deteriorate the characteristics of the Switch.
●Degree of Protection
The Switch was tested and found to meet the conditions necessary to meet the following standard given below. The test checks for water intrusion after immersion for a specified time period, not for switching operation underwater.
JIS C0920: Degrees of protection provided by enclosures of electrical apparatus (IP Code)
IEC 60529: Degrees of protection provided by enclosures (IP Code)
Degree of protection: IP67(check water intrusion after immersion for 30 min. submerged 1m underwater)
●Protection Against Chemicals
Prevent the Switch from coming into contact with oil or chemicals.
Otherwise, damage to or deterioration of Switch materials may result.
Correct Use
●Mounting
Use M2.3 mounting screws with plane washers or spring washers to securely mount the Switch. Tighten the screws to a torque of 0.20 to 0.29 Nm {2 to 3 kgfcm}.
●Wiring Molded Lead Wire Models
When wiring molded lead wire models, ensure that there is noweight applied on the wire and that the wire is not bent. Otherwise, damage to the Switch or deterioration in the sealingmay result.
●Using Micro Loads
Even when using micro load models within the operating range shown below, if inrush/surge current occurs, it may increase the contact wear and so decrease durability. Therefore, insert a contact protection circuit where necessary.